About car and smoke

Dodane: 06-08-2016 10:26
About car and smoke premium oil for Maserati

Fast wearing parts for cars

Due to the geographical location of Polish among the most frequently mentioned car parts are the tires. In winter, most drivers choose to mount tires designed for harsh weather conditions. Excessive use of a Particular type of tire small to have an adverse effect on Their Subsequent performance. Therefore, it is important to regularly held reviewed accompanied by checking the condition of the tires and the like equipment. It is servicing a car you can discover the many defects That can be quite easily removed and Which constitute the safety of passengers using the vehicle. So Consider carefully check the status of our car.


In modern usage

The word "engine" derives from Old French engin, from the Latin ingenium?the root of the word ingenious. Pre-industrial weapons of war, such as catapults, trebuchets and battering rams, were called "siege engines", and knowledge of how to construct them was often treated as a military secret. The word "gin", as in "cotton gin", is short for "engine". Most mechanical devices invented during the industrial revolution were described as engines?the steam engine being a notable example. However, the original steam engines, such as those by Thomas Savery, were not mechanical engines but pumps. In this manner, a fire engine in its original form was merely a water pump, with the engine being transported to the fire by horses.

In modern usage, the term engine typically describes devices, like steam engines and internal combustion engines, that burn or otherwise consume fuel to perform mechanical work by exerting a torque or linear force (usually in the form of thrust). Examples of engines which exert a torque include the familiar automobile gasoline and diesel engines, as well as turboshafts. Examples of engines which produce thrust include turbofans and rockets.

When the internal combustion engine was invented, the term "motor" was initially used to distinguish it from the steam engine?which was in wide use at the time, powering locomotives and other vehicles such as steam rollers. "Motor" and "engine" later came to be used interchangeably in casual discourse. However, technically, the two words have different meanings. An engine is a device that burns or otherwise consumes fuel, changing its chemical composition, whereas a motor is a device driven by electricity, air, or hydraulic pressure, which does not change the chemical composition of its energy source.3 However, rocketry uses the term rocket motor, even though they consume fuel.

A heat engine may also serve as a prime mover?a component that transforms the flow or changes in pressure of a fluid into mechanical energy.4 An automobile powered by an internal combustion engine may make use of various motors and pumps, but ultimately all such devices derive their power from the engine. Another way of looking at it is that a motor receives power from an external source, and then converts it into mechanical energy, while an engine creates power from pressure (derived directly from the explosive force of combustion or other chemical reaction, or secondarily from the action of some such force on other substances such as air, water, or steam).5

Devices converting heat energy into motion are commonly referred to simply as engines.6

Źródło: https://en.wikipedia.org/wiki/Engine


In the crankcase

In the crankcase of a vehicle engine, motor oil lubricates rotating or sliding surfaces between the crankshaft journal bearings (main bearings and big-end bearings), and rods connecting the pistons to the crankshaft. The oil collects in an oil pan, or sump, at the bottom of the crankcase. In some small engines such as lawn mower engines, dippers on the bottoms of connecting rods dip into the oil at the bottom and splash it around the crankcase as needed to lubricate parts inside. In modern vehicle engines, the oil pump takes oil from the oil pan and sends it through the oil filter into oil galleries, from which the oil lubricates the main bearings holding the crankshaft up at the main journals and camshaft bearings operating the valves. In typical modern vehicles, oil pressure-fed from the oil galleries to the main bearings enters holes in the main journals of the crankshaft. From these holes in the main journals, the oil moves through passageways inside the crankshaft to exit holes in the rod journals to lubricate the rod bearings and connecting rods. Some simpler designs relied on these rapidly moving parts to splash and lubricate the contacting surfaces between the piston rings and interior surfaces of the cylinders. However, in modern designs, there are also passageways through the rods which carry oil from the rod bearings to the rod-piston connections and lubricate the contacting surfaces between the piston rings and interior surfaces of the cylinders. This oil film also serves as a seal between the piston rings and cylinder walls to separate the combustion chamber in the cylinder head from the crankcase. The oil then drips back down into the oil pan.45

Motor oil may also serve as a cooling agent. In some constructions oil is sprayed through a nozzle inside the crankcase onto the piston to provide cooling of specific parts that undergo high temperature strain. On the other hand, the thermal capacity of the oil pool has to be filled, i.e. the oil has to reach its designed temperature range before it can protect the engine under high load. This typically takes longer than heating the main cooling agent ? water or mixtures thereof ? up to its operating temperature. In order to inform the driver about the oil temperature, some older and most high performance or racing engines feature an oil thermometer.

Due to its high viscosity, motor oil is not always the preferred oil for certain applications. Some applications make use of lighter products such as WD-40, when a lighter oil is desired, or honing oil if the desired viscosity needs to be mid-range.6

Źródło: https://en.wikipedia.org/wiki/Motor_oil